0 of 61 Questions completed
Questions:
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading…
You must sign in or sign up to start the quiz.
You must first complete the following:
0 of 61 Questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
Which of the following electrical installations does BS 7671 not apply?
BS 7671 includes the requirements for
BS 7671 requires protection against electric shock to be provided by basic and fault protection. One method common to both modes of protection is
Which one of the following types of electrical installation is not covered by BS 7671?
When applied to a electric surface heating systems, BS 7671 may need to be supplemented by the requirements or recommendations of which other documents?
BS 7671 provides requirements for safety against the risks of …
BS7671 applies to
BS 7671 does NOT provide requirements for safety against the risk of …
The selection of the type of wiring and method of installation is not influenced by
Voltage range covered by BS 7671
Band II voltage exceeds
A protective conductor connecting exposed-conductive-parts of equipment to the main earthing terminal is known as the
Band 1 voltage value isÂ
Mechanically and electrically integrated assembly of PV modules is
An earthing arrangement in which two earth electrodes are used is called
To ensure continuity of supply to one part of the installation in the event of failure of another part, one approach is
An assessment must be made of the harmful effects of harmonic currents of equipment on other electrical equipment. This assessment is
Every installation shall be divided into circuits as necessary in order to
Which one of the following is not a potential characteristic of equipment to be considered for harmful effects on other equipment?
When making an assessment of the frequency and quality of maintenance, a factor to be considered is that
A 32 A BS 88-3 fuse with Uo of 230 V has a maximum tabulated Zs for 5 seconds disconnection of
Which of the following is a requirement in terms of fault protection where the protective measure of electrical separation is employed?
An RCD can be used as additional protection in the event of failure of the provision for basic protection when the RCD has a rating not exceeding
Basic protection can be provided by
BS7671 applies to?
When considering the compatibility of a large three-phase AC motor, with
regards to the other equipment installed on-site we should consider the effects
of
An Extra-low voltage system which is electrically separated from earth and is
supplied by a recognised safety source is defined as
The maximum disconnection time for a 16 A final circuit, where Uo = 230 V AC,
forming part of a TN system is
To ensure compliance with BS7671, all overcurrent protective devices without
back-up protection on the supply side must be capable of :
Which of the following methods should be adopted where fixed equipment with
a high surface temperature is likely to have an adverse effect on adjacent
materials?
If a protective device has operated and restoration of the supply is likely to
cause danger the re-closure must be
Which of the following methods provides protection against both Basic and
Fault Protection?
In order to comply with BS7671, the maximum permitted earth loop impedance
for a 32 A BS 88-G fuse protecting a cooker is
Correct co-ordination between fuse ratings in an electrical system is termed
To provide protection against electric shock, the protective measure of double
insulation relies on basic insulation and
The maximum disconnection time for a circuit supplied at reduced low voltage
is
Where particular risks of fire exist in an area of high density occupation with
difficult conditions of evacuation, the external influence code would be
Where the overcurrent protective device is intended to afford protection against
overload, I2 must not exceed IZ by
In AC systems additional protection by RCD’s rated at 30 mA or less must be
used
The earth fault loop impedance Zs for a final circuit is determined by
Metal conduits, trunking and consumer units must comply to
Where an installation forms part of a TN-C-S system, the main protective
bonding conductor must have a minimum cross sectional area of
Where an installation of street furniture forms part of a TN system using 10 mm2 neutral, the main protective bonding conductor must have a minimum cross sectional area of
Which of the following is used to determine the rated current of an overcurrent
protective device
The design of a safety circuit should include which one of the following
PVC/PVC twin + cpc flat cable, when installed in a wall in a dwelling at a depth
of less than 50 mm, and earthed metallic conduit, are permitted by regulations
to be run
A label marked with the words ‘Safety Electrical Connection – Do Not Remove’
must be fixed at or near
A copper earthing conductor not mechanically protected but protected against
corrosion buried in soil. The minimum cross-sectional area of the earthing
conductor should be
A firefighter’s switch should be installed at not more than
Cross sectional area of ring network conductor is
The type of distribution system known as PME is an earthing arrangement
found in a
IP code for swimming pool Zone 0
IP code for bathroom  Zone 1
The purpose of the integral test button of an RCD is to check the
The maximum recommended voltage drop for a 230 V single-phase lighting
circuit, fed from the public LV distribution system is
What does PEI stand for ?
A recognised suitable supply for safety services is a
A reduced 250 V DC test of insulation resistance may be applied to a 230 V
distribution board when
Which one of the following tests can only be carried out after the supply is
connected
The recommended test voltage (DC) and minimum insulation resistance value
for an SELV circuit is
In agricultural premises, in the absence of manufacturer’s instructions, heating
equipment should be placed at a distance from livestock, not less than